Nationwide SunTek Window Tint Lifetime Warranty

SunTek Window Films

Automotive Film Limited Warranty

Carbon Series (Lifetime Limited Warranty)

Warranty Info

SunTek warrants against fading, peeling, cracking, adhesive failure, and delamination for as long as the original customer owns the vehicle.

The obligation of SunTek under this warranty is limited to replacement of products not conforming to the warranty. This product is to be used in compliance with all applicable state or provincial laws. Installation of this product in a manner that violates state or provincial law is a misuse of the product and voids all warranties, expressed or implied, including but not limited to the warranty of merchantability. SunTek shall not be liable in any manner for whatsoever for damages related to the use of this product in illegal manner.

Warranty Registration: To validate your warranty please detach and mail the postcard at the bottom of this warranty. Note: All information on this card must be filled out and returned within 30 days of installation to validate warranty. Warranty is provided to the original customer and non-transferable.

To Make A Claim: Retain this warranty registration card and proof f purchase in order to process any claim. Any customer desiring warranty service should contact the nearest authorized SunTek installer or write to:

Commonwealth Laminating & Coating, Inc.

P.O. Box 4668

Martinsville, VA 24115-4668

276-632-4991

Window Film Care: To extend the life and looks of your SunTek Automotive Film and to maintain your warranty coverage, certain care and maintenance should be followed. Do not roll down filmed windows for a period of 5 days until the film has properly adhered to the glass. Do not wash the film for thirty (30) days after installation. Do not use abrasive cleaners or coarse clothes. Use a mild soap and a clean, soft cloth or synthetic sponge.

There are no other warranties either expressed or implied. This warranty applies only to manufacturing quality. The installation dealer is responsible for the quality of the installation on your vehicle. Warranty not valid without roll numbers.

SunTek Limited Lifetime Warranty Validation Requirements:

• Dealer information must complete to validate SunTek warranty, including vehicle Year / Make / Model / Vehicle ID / Installation Date and Installation Price
  
• Roll numbers must be included for front sides, rear sides, rear window and additional glass to validate SunTek warranty.
  
• Dealer signature and phone number must be included to validate SunTek warranty.
  
• Customer name, address, phone number and signature must be included to validate SunTek warranty.
  

Note: Void if not returned in 30 days and completely filled out. Roll numbers must be included.

Detach and mail warranty card to:

Commonwealth Laminating & Coating, Inc.

P.O. Box 4668

Martinsville, VA 24115-4668

276-632-4991

Additional Product Warranty, Care & Maintenance Information

Our SunTek films require a reasonable curing time to facilitate proper bond to the glass. During this curing time, some NORMAL changes may be noticed. Below is a list of the things to look for, and should be expected to occur, including:

Allow film to cure for 3 days before lowering the windows. Curing time will be approximately 30 days. Windows should not be washed inside the vehicle during that time.

If haziness and/or a smoky or milky appearance occur, it is the soapy solution used during installation of your new window film. This will become less noticeable as the curing time passes.

All water bubbles will dry out, but a few small particles may be seen from the exterior after the curing time has been completed. Generally, these particles cannot be noticed from a reasonable distance from the vehicle. These particles can be attributed to pinhead sized translucent globules of adhesive, or detactifier that have not cured to a perfect clarity.

On occasion the technician will capture a grain of dust or sand that cannot be eliminated and in rare cases this to may be normal. You may expect your film to highlight imperfections in the glass as they become more noticeable with the addition of reflective metalized window films.

Sometimes a customer feels that they see a defect in the film when in fact it is in the glass...It is quite natural that we should look closely at the new purchase, but at times we see things that were always there but never noticed. Observe the installations from 2 to 3 feet away from the surfaces tinted. This is the way we normally look through a window and this is the way you should observe your new window film...looking through it, not at it.

There may be a thin Line of light bordering your window film. This light is in proper keeping with the specific installation instructions.

In situations involving the installation of film on large pieces of glass, it may be necessary to splice two panels of film together with the seam in a vertical or horizontal direction. In such cases all care will be taken to use this accent seam to the aesthetic advantage of your vehicle.

Cleaning can be done with a soft towel or squeegee. Never use ammonia based products, vinegar or any abrasive materials or pads. Good cleaning solutions may include water, soap and water, or alcohol and water.

Have You Recently Re-Located To Sunny Arizona?

If you have had SunTek window film previously installed anywhere in the U.S.A. and may be experiencing problems with the product installation, call our Warranty Claims Department for all manufacturers submission and replacement services at 602.524.0807 and we will be more than happy to assist you in replacing any warranty claim related issues at absolutely No Charge To You!